- DOWNLOAD Detroit Diagnostic Link (DDDL 8.09) Engineering level 10
$40.00Add to cart
- DOWNLOAD Freightliner diagnostic software ServiceLink 4.9.6
$30.00Add to cart
- DOWNLOAD Noregon JPRO Commercial Fleet Diagnostics 2017 v3 (Copy)
$40.00Add to cart
- Description
- Tags
- Reviews (0)
Description
Circuit Description
The variable geometry turbocharger (VGT) is electronically activated by the VGT actuator. The VGT actuator is a smart device and receives information via the J1939 data link from the primary engine control module (ECM). The VGT actuator performs its own diagnostics and reports malfunctions back to the primary engine ECM, using the J1939 data link. The ECM then decodes the error message and converts it to a fault code.
Component Location
The VGT actuator is located on the turbocharger bearing housing.
Conditions for Running the Diagnostics
This diagnostic runs when the keyswitch is initially turned to the ON position.
The keyswitch must be turned OFF for more than 30 seconds before this diagnostic will run at initial key ON.
Conditions for Setting the Fault Codes
The Variable Geometry Turbocharger (VGT) actuator position was not known during initial power ON.
Action Taken When the Fault Code is Active
The ECM illuminates the amber CHECK ENGINE lamp and/or the Malfunction Indicator Lamp (MIL) immediately when the diagnostic runs and fails.
VGT actuation will be disabled.
Exhaust Gas Recirculation (EGR) valve operation will be disabled.
Engine torque will be reduced if the engine is operated for an extended period of time with this fault active.
Conditions for Clearing the Fault Code
To validate the repair, perform a key cycle, and leave the keyswitch in the ON position for 1 minute. Note that the keyswitch must be completely turned OFF for more than 30 seconds before this diagnostic will run at initial key ON.
The fault code status displayed by INSITE™ electronic service tool will change to INACTIVE immediately after the diagnostic runs and passes.
The ECM will turn off the amber CHECK ENGINE lamp immediately after the diagnostic runs and passes.
For On-Board Diagnostics (OBD) engines, the ECM will extinguish the Malfunction Indicator Lamp (MIL) after three consecutive trips where the diagnostic runs and passes.
The Reset All Faults command in INSITE™ electronic service tool can be used to clear active and inactive faults, as well as extinguish the MIL for OBD applications.
Shop Talk
This fault code can only be logged after the VGT actuator has been removed or replaced, and then not installed correctly. The gear alignment between the actuator and the turbocharger housing is misaligned. The correct installation procedure must be followed when replacing the VGT actuator.
Possible Cause:
1) Turbocharger failure
2) VGT Actuator failure
3) ECM calibration
Related
Tags: , 14, 2018, 641, 6432, Actuator, CM2450, Code, Controller-, Cummins, Fault, FMI, Instructions, Newer, PID, Special, SPN, VGT, X124B, X15
Reviews
There are no reviews yet.
Be the first to review “Cummins X15 CM2450 X124B (2018 & Newer) Fault Code: 6432 PID: SPN: 641 FMI: 14 VGT Actuator Controller- Special Instructions”
Categories Cumminz, DTC TRUCKS, Tags , 14, 2018, 641, 6432, Actuator, CM2450, Code, Controller-, Cummins, Fault, FMI, Instructions, Newer, PID, Special, SPN, VGT, X124B, X15
- DOWNLOAD Detroit Diesel Drumroll Engineering 7.06 DDDE v7.06
$25.00Add to cart
See AlsoHelpful Guide: SPN 641 FMI 7 Cummins (FMI 9, FMI 11, FMI 13)Complete Cummins Fault Codes List (Cummins SPN Codes PDF)Cummins ISB4.5 CM2150 Fault Code: 1898 PID: SPN: 641 FMI: 13 VGT Actuator Controller - Out Of Calibration. - EcuForce TruckCummins ISB6.7 CM2350 (2013-17) Fault Code: 6432 PID: SPN: 641 FMI: 14 VGT Actuator Controller - Out Of Calibration. The VGT Actuator Has Been Installed Incorrectly. - EcuForce Truck - DOWNLOAD IDSS Isuzu G-IDSS 2020 Diagnostic Service System [08.2020] Release Full
$125.00Add to cart
- DOWNLOAD JPRO 2022 V3 software professional download ( JPRO 2022 V3 ) 1 PC
$88.00Add to cart
- Related Products
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
Quick View
Add to wishlist
CompareAdd to cart
AllisonDTC TRUCKS
JPRO
DOWNLOAD Noregon JPRO Commercial Fleet Diagnostics 2017 v3 (Copy)$40.00Add to cart
cummisznn
Cumminmms Insite pro 8.9 Diagnostic Software$80.00Add to cart
Trucks software
JPRO Diagnostic Software Download 2024$100.00Add to cart
Trucks software
AGCO EDT 2023.10 Electronic Diagnostic Tool 1.125$120.00Add to cart
Trucks software
DOOSAN diagnostic software DMS-5 3.1.3 [2023.11] 1PC$106.00Add to cart
Trucks software
Bendix Acom Pro 2023 V1 diagnostic software 1PC$83.00Add to cart
Trucks software
VOLVOUU PTT TECH TOOL 2.8.220 2023 Last version 1pc$200.00Add to cart
Trucks software
Download Allison Doc Premium Update 2023 v2$105.00Add to cart
BOBCAT
SERVICE MANUAL BOBCAT 2000 sms$45.00Add to cart
Trucks software
DOWNLOAD VOLVOUU VODIA 5.2.50 works with VOCOM + video$95.00Add to cart
Thermo King
DOWNLOAD Thermo King EPC 2012$45.00Add to cart
CARRIE
$45.00Add to cart
BOBCAT
SERVICE MANUAL BOBCAT 450 453 sms$45.00Add to cart
BENDIX
SERVICE MANUAL Bendix ABS GEN 4 AND GEN 5$45.00Add to cart
BOBCAT
SERVICE MANUAL BOBCAT 7753 sms$45.00Add to cart
CAT
DOWNLOAD Caterpillar ET 2022A Electronic Technician + Factory Password (1PC)$96.00Add to cart